Precise Control and Long Service Life with Axial Piston Pumps

Product Description

Precise Control and Long Service Life with Axial Piston Pumps

Variable displacement axial piston pumps introduction:

Our axial piston pumps are built to last, offering robust construction that withstands the toughest industrial conditions. With their high-pressure capability and advanced engineering, these pumps ensure a long service life while maintaining consistent performance. Opt for our pumps to keep your operations running smoothly, even under the most strenuous conditions.

Hydraulic axial piston pumps main features:

1. Variable displacement axial piston hydraulic pumps

2. Axial piston hydraulic pumps have swash plate structure

3. Be suitable for hydrostatic transmissions with closed-loop circuit

4. Manual servo and hydraulic variable control

5. Axial piston hydraulic pumps with a charging oil pump

6. LPV90 hydraulic variable displacement axial piston pump 

7. Hydraulic piston pump 42Mpa high pressure 

LPV90 Axial piston pumps technical specification:

Notices:

Keep a close eye on the operating temperature of your axial piston pumps. Overheating can be detrimental to pump efficiency and can cause significant damage to hydraulic components. Implement temperature monitoring systems to catch any abnormal increases early, allowing you to take corrective action before any serious damage occurs.

Factory Production & Inspection Evidence

The LPV90-MA-R-23 is produced by Shandong Highland Hydraulic Seiko Co., Ltd., with the produced units recorded for traceability. The supplied project record lists a production quantity of 100 units, and the factory test report identifies the tested unit by Component No. 02604200203002.

• LPV – LPV series closed axial piston pump
• 90 – 90 mL/r displacement
• MA – manual servo control
• R – clockwise rotation
• 23 – 23-tooth input shaft (16/32 pitch)

Evidence type: factory production / product identification.

Factory Performance Testing

Factory performance testing of the LPV90-MA-R-23 is recorded on a closed-loop hydraulic pump test bench. The test documentation records Component No. 02604200203002, a test on 2026/4/20 at 9:12, a test temperature of 22.7 °C and a power recovery ratio of 50%. Rated displacement is 90.5 mL/rev and rated pressure is 35 MPa; the test-bench main parameters are a maximum speed of 3200 r/min and a maximum pressure of 42 MPa.

Recorded Test Data

For the LPV90-MA-R-23, the closed-loop report logs speed, pressure, flow, displacement, torque, input power, output power, overall efficiency, volumetric efficiency and charge pressure. Selected recorded points are shown for reference.

Charge pressure: 1.7 MPa; charge flow 22.4 L/min. Figures are reproduced from the original test record; interpretation should follow the test-bench measurement and calculation method.

Engineering Drawing & Dimensions

The LPV70/90-MA-R/L-21/23/14-NN engineering drawing provides the mounting flange, output shaft spline, hydraulic port, control interface and rotation-direction data for the LPV90-MA-R-23. Key interface information includes:

• High pressure ports A and B; leakage ports L1 / L2; oil suction port S
• High pressure relief valves A / B; low pressure relief valve
• Pressure taps Ma / Mb: 9/16-18; servo-cylinder pressure taps (both sides): 9/16-18
• Input shaft spline options: 21 teeth (16/32 pitch), 23 teeth (16/32 pitch), 14 teeth (12/24 pitch), 30° pressure angle
• Input shaft dividing circle diameters: Ø33.34 mm (21T) / Ø36.5 mm (23T) / Ø29.63 mm (14T)
• Control handle spline: 1/4-20 UNC-2A, 24 teeth, diametrical pitch 64/128, OD 9.5 mm (SAE 1963)
• Mounting: 4 bolts M12, 25 mm depth; ports L1 / L2 1 1/16-12; port S 1 5/16-12; relief valve options 32 / 35 / 40 MPa; charge/suction pressure 1.8–2.4 MPa
• Rotation direction R (clockwise) / L (anticlockwise)

Drawing technical requirement: minimum speed 500 r/min, maximum speed 3000 r/min, rated working pressure 30 MPa. Interface dimensions should be confirmed against the engineering drawing before installation.

Quality Control & Final Inspection

Quality control documentation for the LPV90-MA-R-23 is based on product identification, factory test records and engineering specifications. The test report documents the pump's displacement, pressure, speed, flow and output power recorded during closed-loop testing.

• Product model identification
• Hydraulic pump performance testing
• Pressure and speed verification
• Flow and displacement recording
• Torque and power measurement
• Overall and volumetric efficiency recording
• Engineering interface verification

Dimensional inspection · surface and finish inspection · assembly inspection · leakage inspection · rotation (R / L) inspection · port and interface inspection · final inspection before packing.

Project Reference

A project record documents the model for a customer located in Belarus. The record lists Shandong Highland Hydraulic Seiko Co., Ltd. as manufacturer, a quantity of 100 units and a rye harvester application.

• Project: Variable Piston Pump for Belarus
• Model: LPV90-MA-R-23
• Quantity: 100 units
• Application: Rye harvester
• Client: Belarus
• Manufacturer: Shandong Highland Hydraulic Seiko Co., Ltd.
• Drive configuration: Closed circuit hydraulic system

Technical Documents

Technical documents available for the LPV90-MA-R-23 include:

The documents provide displacement, speed, pressure, torque, power, temperature and weight data, confirming the LPV90 as a closed axial piston pump. Records are filed against the unit's component number for reference.

FAQ of variable displacement axial piston pumps: 

Q1: Are you a manufacturer?

A: Yes, we are manufacturer to produce, design and test axial piston hydraulic pumps by ourselves.

Q2: How do you ship the goods and how long does it take to arrive?

A: Ship by air express, it takes 3-5 days to arrive. Airline and sea shipping also optional.

Q3: Do you offer guarantee for the products?

A: Each motor or pump should be tested before shipping, test report can be sent if requested.

Warranty 12 months after shipment for complete assembly.

Q4: What are the payment terms?

A: Full order: 30% as deposit, balance before shipment.

Small order/sample order: Full advance payment.

Q5: Do you test all piston pumps before shipment?

A: Yes, we have 100% test before shipment, we must guarantee pumps quality. 

Whatsapp/wechat/phone:+86 18678785446

E-mail:ld@hldhydraulic.com

QQ:545353883