logo
Latest company news about HIGHLAND YST Hydraulic Test Benches Support Performance Testing for New Hydraulic Pump Development

November 10, 2026

HIGHLAND YST Hydraulic Test Benches Support Performance Testing for New Hydraulic Pump Development

HIGHLAND YST Hydraulic Test Benches Support Performance Testing for New Hydraulic Pump Development

Developing a new hydraulic pump is rarely a matter of a single design iteration. Before a prototype reaches production, engineers need a clear understanding of how it performs across its intended working range. Flow delivery, operating pressure, input speed and oil temperature all form part of that assessment, and each of these parameters has to be measured under controlled, repeatable conditions.

HIGHLAND's YST series hydraulic test benches are built around that requirement. The platform can be configured for hydraulic pump testing, and depending on the selected arrangement it can support the evaluation of both open-circuit and closed-circuit pumps. Measurement functions are chosen to match the development programme rather than being fixed in advance, so the bench reflects the test plan instead of limiting it.

Configuring a Bench Around the Development Programme

Every pump development programme starts with different questions. A team may be focused on volumetric efficiency at high pressure, on the behaviour of a variable-displacement control, or on how quickly the unit reaches a stable operating temperature. Because the YST platform is modular, drive capacity, loading circuit, sensors, fixtures and software functions can be selected to answer those specific questions.

  • Drive and loading — matched to the pump's displacement and rated pressure
  • Instrumentation — pressure, flow, speed, torque and temperature measurement as required
  • Fixtures and plumbing — adapted to the prototype's mounting and port configuration
  • Software functions — data acquisition, real-time display and recording

A Typical Development Scenario

Consider a team developing a variable-displacement pump for agricultural machinery. The unit will operate across a wide range of pressures and shaft speeds, and the prototype must be examined at defined operating points. Testing at those points allows engineers to compare measured output against the design target and to identify the conditions that need further investigation — for example, a drop in flow delivery at elevated pressure or an unexpected rise in case drain flow.

Because the same operating points can be repeated, the comparison is made on a like-for-like basis rather than on isolated spot readings. The test conditions — speed, displacement setting, oil temperature and fluid type — are recorded alongside the measurements, so the data remains meaningful when it is reviewed weeks or months later.

Turning Measurements into Performance Curves

The results from a suitably configured test bench also support the preparation of performance curves. A pressure-and-flow curve gives the development team a straightforward way to review how pump output changes as operating pressure increases. Plotted against measured data, it shows where the pump behaves as predicted and where it begins to fall away from the design intent.

Recorded Parameter Why It Matters
Operating pressure Defines the load point for each measurement
Flow delivery Primary indicator of volumetric performance
Input speed Required to normalise flow and torque data
Oil temperature Affects viscosity and therefore internal leakage
Fluid type Needed to keep test conditions comparable

Evaluating Design Revisions

When a prototype is revised — a modified valve plate, a different clearance, a new control spring — the effect of that change has to be isolated. Repeating selected tests under comparable conditions gives the team a direct before-and-after comparison. Where the bench includes suitable torque and speed measurement, input-power data can also be included in the assessment, allowing mechanical efficiency to be reviewed alongside hydraulic performance.

Real-Time Display and Data Recording

Computer-equipped HIGHLAND configurations offer real-time display and data recording for analysis. Instead of transcribing gauge readings by hand, the engineer sees flow, pressure, speed and temperature as the test runs, and the recorded data set can be exported for curve plotting, statistical review or inclusion in a design review report. The depth of that function depends on the sensors and software selected with the bench, and the required drive capacity, loading circuit, sensors, fixtures and software functions all follow from the pump and the planned tests.

latest company news about HIGHLAND YST Hydraulic Test Benches Support Performance Testing for New Hydraulic Pump Development  0

What to Define Before Ordering a Test Bench

  1. The pump types to be tested — open circuit, closed circuit, or both
  2. Maximum displacement, pressure and input speed required
  3. Which parameters must be measured and at what accuracy
  4. Whether performance curves and input-power assessment are needed
  5. How data should be recorded, displayed and exported

Practical Value for Manufacturers and Research Teams

For hydraulic pump manufacturers and research teams, a suitably configured test bench provides a practical way to turn prototype measurements into evidence. That evidence supports design review, informs the next iteration, and gives the development team a documented record of how the prototype behaved under defined conditions.

HIGHLAND's YST series hydraulic test benches are available in configurations adapted to different pump types and testing requirements. To discuss the right arrangement for a specific development programme, contact the HIGHLAND technical team.