Drying Machine Hmf130 Heavy Duty Hydraulic Motor Effective

Product Description

Highland Drying machine Heavy duty hydraulic motor cost-effective

Quick Detail:

·Cast iron housing

·Hydraulic components

·Model HMF130

·Hydraulic system power components

·Principle hydraulic transmission

·Features easy maintenance

·Simple layout

·System Solutions

·Work fast

·Fully replace imported products

·Patent certificate certification

·Application mobile crusher heavy duty hydraulic motors

·1 year warranty

Description:

The service life of Highland heavy duty hydraulic motors is related to the usual maintenance, the quantity and quality of the hydraulic oil, and the cleanliness of the oil. It is also an effective way to prolong the life of the heavy duty hydraulic motors to avoid the wear and tear of the friction pair of the heavy duty hydraulic motors caused by the particles in the oil. The higher the cleanliness of the hydraulic oil, the longer the service life of the hydraulic motor.

Highland heavy duty hydraulic motors are widely used in high pressure, big flow, power systems and the flow needs to adjust the situation, such as machine tools, metallurgy, forging, mining and lifting hydraulic transmission system.

Highland heavy duty motors is a typical volumetric fluid machine, driven by the prime mover, converting the input mechanical energy into the pressure energy of the liquid, and then inputting it into the system in the form of pressure and flow. Heavy duty motors is the power source of the hydraulic system.

Highland hydraulic motor offers variable displacement medium pressure heavy duty motor for closed circuit mobile applications. Compact, quiet and efficient, heavy duty motor deliver a operating pressure of up to 42Mpa.

1. Be suitable for hydrostatic transmissions with closed-loop circuit.
2. Manual servo and hydraulic variable control.
3. Variable displacement motors heavy duty with charging oil motor.

Highland HMF Series Technical parameter:

Notices:

Hydraulic oil

The suitable replacement period for hydraulic oil in a sealed tank system is 2000 hours, and more often if the hydraulic oil is contaminated with water or other external materials or subjected to abnormal operating conditions.

As a general recommendation, the 10µ inlet oil filter should be replaced every spring or every 1500 hours (whichever occurs first) on a sealed tank system, or in an open tank system with an air filter fill cap. The oil filter should be replaced every 500 hours.

Heat Exchanger

The heat exchanger core and fins are kept clean at all times for maximum cooling and system efficiency, and the exterior of the heat exchanger is checked daily for blockages and cleaned as needed.

Application:

Mixer truck: concrete mixer truck, cement mixer truck;

Coal mining machinery: scraper;

Industry: pharmaceutical machinery;

Transport vehicles: road rollers, concrete pump trucks, stabilized soil mixers

HMF130 Factory Production & Inspection Evidence

During manufacturing and inspection at our plant, this hydraulic motor was photographed. Such factory-floor images offer straightforward visual confirmation of the actual product build, covering housing, drive shaft and port layout, as it stands before dispatch.

Factory Evidence

• Real hydraulic motor shown as photographed at the factory
• Visual check of the product housing and drive shaft before dispatch
• Ports and mounting configuration confirmed to match the relevant model specification
• Final inspection conducted to the product’s technical requirements

Evidence Type: Factory Production / Visual Inspection

Application: Hydraulic motor systems

Product Status: Production / Pre-shipment Inspection

Actual Factory Photo — Hydraulic Motor During Production & Inspection

Factory acceptance for the HMF130-23 is a full run on the closed-loop motor test stand. The report for component No. 02604080203001 is dated 2026/4/8, 11:23, and was taken at 30 ℃ against a rated displacement of 130 mL/rev, 2900 r/min maximum speed and 38 MPa maximum pressure (rated pressure 35 MPa); the rig shows a 20 % power-recovery ratio.

HMF130 Recorded Test Data

Measured data captured for the HMF130-23 during its closed-loop motor test (component No. 02604080203001; 2026/4/8 11:23; 30 ℃; charge pressure 1.2 MPa):

Every number is taken directly from the source test report; the charge pressure stays at 1.2 MPa.

HMF130 Quality Control & Inspection

Inspection of the HMF130-23 centres on the closed-loop test bench. Once assembled, the motor is run so that displacement, speed, pressure, flow, torque and its overall/volumetric efficiency can be confirmed, and any external leakage is ruled out; acceptance follows only if the values are on specification. The report issued with this unit documents that same routine.

HMF130 Engineering Drawing

For the HMF130-23 the drawing is the HMF110/130-21/23 motor sheet. The drive shaft is a 23-tooth involute spline (16/32 pitch) with module 1.588, 30° pressure angle and a 36.52 mm pitch-circle diameter. A SAE flange fixed by four M12 bolts (25 mm deep) is used; main ports A and B take 7/8-14 UNF-2B threads, L1 and L2 are leakage ports, and 9/16-18 pressure taps at 15 mm depth serve the flushing and relief valves. CW/CCW rotation is selectable.

HMF130 Application / Project Evidence

Application evidence for the HMF130-23: the unit originates from a 50-piece order for a Kyrgyzstan potato-harvester application (project “Variable Piston Pump for Kyrgyzstan”, client in Kyrgyzstan). Its duty on the harvester is the closed-circuit hydrostatic drive, covering travelling as well as the working functions. The particulars that follow are reproduced from the project documentation.

HMF130 Technical Documents

For the HMF130 closed axial piston motor, the following technical documents are on file, covering ratings, bench-test results and the mounting drawing. They form the document set for this product and can be provided to qualified buyers on request.

• HMF130 motor technical parameter sheet
• Closed-loop hydraulic motor test report (component No. 02604080203001)
• Engineering / outline drawing (HMF110/130-21/23)
• Model selection table (displacement and output shaft)

These documents can be requested through our sales team.

FAQ

 

Q1. Can I have a sample order for mobile crusher heavy duty hydraulic motors ?

A: Yes, we welcome sample order to test and check quality.

 

Q2. What about the lead time?

10 to 15 days for samples, mass production according to MOQ

 

Q3. Do you have any MOQ limit for mobile crusher heavy duty hydraulic motors ?

A: Low MOQ, 1pc for sample checking is available.

 

Q4. How do you ship the goods and how long does it take to arrive?

Ship by sea, it generally takes 15-20 days to arrive, and air is also optional.

 

Q5. How to proceed an order for mobile crusher heavy duty hydraulic motors ?

A: Firstly let us know your requirements or application.

Secondly We quote according to your requirements or our suggestions.

Thirdly customer confirms the samples and places deposit for formal order.

Fourthly We arrange the production.

 

Q6: Do you offer guarantee for the products?

A: Yes, we offer 1 years warranty to our products.

 

Q7: How to deal with the faulty?

A: Firstly, our products are produced in strict quality control system.Secondly, we will inspect the defective pump and motor, and then respond according to the actual situation